Barnes 084647, Model 4SE15044HL, 4SE-HL Series, Sewage Pump, 15 HP, 460 Volts, 3 Phase, 4" Flanged Horizontal Discharge, 800 GPM Max, 90 ft Max Head, 40 ft Cord, Manual, Double Seal
FREE SHIPPING ON THIS ITEM ! Offer applies to the lower 48 states and excludes Alaska, Hawaii, APO/FPO and international orders. Free standard shipping applies to U.S. orders only and to select items that meet UPS Standard Ground container/cube requirements. Free Shipping
FEATURES
Barnes 4SE-HL Submersible Non-Clog Sewage Pump
This is a submersible, non-clog sewage pump designed for typical raw sewage applications. This pump has a double seal and can handle spherical solids up to 3 inch in diameter. It has a torque curved, oil filled, squirrel cage induction motor.
Features
-
4" 125lb, flanged horizonal discharge
-
Motor housing, and seal plate are cast iron ASTM A-48, Class 30
-
Volute is cast iron ASTM A-48, Class 30, with bronze wear ring
-
Impeller has a 2 vane enclosed design with pump out vanes on back side
-
416 stainless steel shaft
-
Buna-N square rings and diaphragm
-
300 series stainless steel hardware
-
304 stainless steel lifting bail
-
Double mechanical seal design made of Carbon/Ceramic/Buna-N with an oil filled pressure equalized reservoir
-
Single row, oil lubricated, radial load upper and lower ball bearings
-
Moisture sensor (Normally Open) and temperature sensor (Normally Closed) require relay in control panel
-
40 ft. cord with epoxy sealed housing with secondary pressure grommet for sealing and strain relief
Brand | Barnes |
Mfg. Number | 084647 |
Model | 4SE15044HL |
Series | 4SE-HL |
Product Type | Sewage pump |
Application | Raw sewage |
Operation | Manual |
Horsepower | 15 HP |
Voltage | 460 Volts |
Phase | 3 |
Frequency | 60 Hz |
Speed | 1750 RPM |
Max. Solid Size | 3" |
Impeller Type | 2 vane, enclosed |
Pump Housing Material | Cast iron |
Discharge Connection | 4" flange 8 bolt horizontal |
Impeller Material | Cast iron |
Seal Type | Dual |
Maximum Flow | 800 GPM |
Maximum Head | 90 ft |
Paint | Air dry enamel |
Thermal Protection | Control panel required |
Power Cord Length | 40 ft |
Motor Casing Material | Cast iron |
Motor Shaft Material | 416 stainless steel |
Shaft Seal | Carbon/Ceramic/Buna-N |
Motor Design | NEMA B |
Service Factor | 1.15 |
Full Load Current | 19 Amps |
Locked Rotor Current | 80 Amps |
Max. Temperature (Continuous) | 104°F |
Power Cord Size | 6/4 |
Cord Type | SOW |
The Barnes 4SE-HL series of submersible, non-clog sewage pumps is designed for typical raw sewage applications. This series of pumps has a double seal and can handle spherical solids up to 3 inch in diameter. The 4SE-HL series has torque curved, oil filled, squirrel cage induction motors. Barnes solids handling pumps are constructed of durable cast iron with oil-filled motors to provide a pump tough enough to meet almost any application need. Features
-
4" 125lb, flanged horizonal discharge
-
Motor housing, and seal plate are cast iron ASTM A-48, Class 30
-
Volute is cast iron ASTM A-48, Class 30, with bronze wear ring
-
Impeller has a 2 vane enclosed design with pump out vanes on back side
-
416 stainless steel shaft
-
Buna-N square rings and diaphragm
-
300 series stainless steel hardware
-
304 stainless steel lifting bail
-
Double mechanical seal design made of Carbon/Ceramic/Buna-N with an oil filled pressure equalized reservoir
-
Single row, oil lubricated, radial load upper and lower ball bearings
-
Moisture sensor (Normally Open) and temperature sensor (Normally Closed) require relay in control panel
-
40 ft. cord with epoxy sealed housing with secondary pressure grommet for sealing and strain relief
BARNES 4SE-HL SERIES SEWAGE PUMPS |
Barnes 4SE-HL Series Sewage Pumps
Model Comparison Chart
Model | Discharge (Flanged Horizontal) | HP | Voltage | Phase | GPM | Max. Head |
4SE7534HL | 4" | 7.5 | 230 | 3 | 640 | 50' |
4SE7544HL | 4" | 7.5 | 460 | 3 | 640 | 50' |
4SE11334HL | 4" | 11.3 | 230 | 3 | 750 | 72' |
4SE11344HL | 4" | 11.3 | 460 | 3 | 750 | 72' |
4SE15034HL | 4" | 15 | 230 | 3 | 800 | 90' |
4SE15044HL | 4" | 15 | 460 | 3 | 800 | 90' |
4SE7524HL | 4" | 7.5 | 230 | 1 | 640 | 50' |
PERFORMANCE CURVES |
DIMENSIONS |
SPECIFICATIONS |
REPAIR PARTS |
TROUBLESHOOTING |
SPECIFICATIONS |
Barnes 4SE-HL Series Sewage Pump Specifications |
INSTALLATION MANUAL |
Barnes 4SE-HL Series Sewage Pump Installation Manual |
Pump Products application engineers are standing by to help you find the right pump, as well as to provide price quotes, stocking availability and shipping information. Call our toll free number 1-800-429-0800 to speak to an expert today.
Call Our Sales Counter For Assistance, Price Quotes, Availability & To Place An Order
Inspector Pumphead & Our Customer Service Representatives Are AvailableMon-Fri 7:30 am to 5:00 pm EST
Call Toll Free: 800-429-0800
*Note: Picture is illustrative and may not reflect the actual product.*