Available For Order! ((Usually Ships 3-5 Days))This product is direct shipped from the manufacturer. The estimated shipping time may vary depending on the manufacturers stock, backlog or delay. If you would like to confirm the manufacturers lead time for this item, call our Pump Products sales team at 800-429-0800 between the hours of 7:30 A.M. - 4:30 P.M. E.S.T. FREE SHIPPING ON THIS ITEM ! Offer applies to the lower 48 states and excludes Alaska, Hawaii, APO/FPO and international orders. Free standard shipping applies to U.S. orders only and to select items that meet UPS Standard Ground container/cube requirements. Free Shipping
Some manufacturers require internet retailers to display a price at or above manufacturers established MAP ("Minimum Advertised Price").
Since our price for this product is lower than MAP, the manufacturer does not allow us to display our lowest price until you place the product in the shopping cart. This allows us to continue offering our lowest prices while staying consistent with product manufacturers policy.
This process does not require you to purchase the product - it can be easily removed from shopping cart if needed.
Mon-Fri 7:00 am to 6:00 pm EST
Sat 8:00 am to 4:30 pm EST
Call Toll Free: 800-429-0800
"Ask Inspector PumpHead"
Our Friendly Staff At PumpProducts.com Can Assist You In Placing Your Order.
Sales Representatives Available!
Mon-Fri 7:00 am to 6:00 pm EST
Sat 8:00 am to 4:30 pm EST
Gould 2GAX Series Submersible Dual Seal Grinder Pump
This submersible, dual seal, grinder pmp is capable of grinding municipal, commercial and industrial sewage.
Features
Cutter system is designed to reduce sewage to a fine slurry
Cast iron, semi-open, non-overloading multi-vane design impeller with pump-out vanes for mechanical seal protection
Cast iron, volute type for high efficiency. Adaptable for slide rail system
Two coat paint system for superior surface protection
Float Leakage Sensor (FLS): a small internal float switch is used to detect the presence of water in the stator chamber. Standard on all models
Leakage Sensor Detector Circuit: The FLS, when activated, will cause the patented 24 volt MiniCAS monitoring relay to signal an alarm and, if desired, stop the pump. The MiniCAS 24 volt relay can be ordered separately for installation in a control panel by a UL or CSA certified panel shop or as a built-in option in our control panel
Maximum temperature rating: 104º F (40º C) continuous duty
Tandem mechanical seals
Fasteners are 300 series stainless steel
Rotating cutter is chrome alloyed cast iron
Cutter ring is hardened 316L stainless steel
Cast iron parts are ASTM A-48, Class 35B
Air-filled, NEMA type B squirrel cage induction motor
NEMA type B
Class F, 311º F (155º C) insulated stator winding
60 Hertz
Motor shaft is 431 series stainless steel, taper collet design
Oversized, pre-greased upper and lower ball bearings
Power cord is 30 feet standard, single jacket, 6 conductor combination power and control cable. Optional 100 foot lead is available
Designed for a maximum of 15 evenly spaced starts per hour
Built-in thermal sensors provide an over temperature signal to the Mini CAS (Control and Status) monitoring relay mounted in the control panel. The Mini CAS can be ordered separately or ordered as an option in our control panel
Common pump motor shaft and compact seal design permit short overhang minimizing shaft deflection
Motor casings have integral cooling ribs for maximum heat dissipation
Shaft mounting is a robust maintenance free design featuring pre-greased ball bearings
The junction chamber is completely sealed off from the surrounding liquid and incorporates a separate gland assembly with a strain relief clamp
Also available in optional Explosion Proof construction. Explosion Proof motor listed Class 1, Division 1, Groups C and D. These units are FM approved
Note: Single phase units require capacitors and start relays for proper operation. See panels BCP5 R13
