Zoeller 31-0057, 36" x 36" Duplex Fiberglass Basin (10 ft Stack) With Steel Solid Cover, 3" Vent, 2" Discharge
Zoeller 31-0057, 36" x 36" Duplex Fiberglass Basin (10 ft Stack) With Steel Solid Cover, 3" Vent, 2" Discharge
SKU #: 31-0057
Brand: Zoeller
Available For Order! ((Usually Ships 3-5 Days))This product is direct shipped from the manufacturer. The estimated shipping time may vary depending on the manufacturers stock, backlog or delay. If you would like to confirm the manufacturers lead time for this item, call our Pump Products sales team at 800-429-0800 between the hours of 7:30 A.M. - 4:30 P.M. E.S.T. FREE SHIPPING ON THIS ITEM ! Offer applies to the lower 48 states and excludes Alaska, Hawaii, APO/FPO and international orders. Free standard shipping applies to U.S. orders only and to select items that meet UPS Standard Ground container/cube requirements. Free Shipping
Some manufacturers require internet retailers to display a price at or above manufacturers established MAP ("Minimum Advertised Price").
Since our price for this product is lower than MAP, the manufacturer does not allow us to display our lowest price until you place the product in the shopping cart. This allows us to continue offering our lowest prices while staying consistent with product manufacturers policy.
This process does not require you to purchase the product - it can be easily removed from shopping cart if needed.
Mon-Fri 7:00 am to 6:00 pm EST
Sat 8:00 am to 4:30 pm EST
Call Toll Free: 800-429-0800
"Ask Inspector PumpHead"
Our Friendly Staff At PumpProducts.com Can Assist You In Placing Your Order.
Sales Representatives Available!
Mon-Fri 7:00 am to 6:00 pm EST
Sat 8:00 am to 4:30 pm EST
Zoeller Duplex Fiberglass Basin and Steel Solid Cover
This fiberglass basin is ideal for use in residential, commercial and industrial applications.
Features
Sewage basins are watertight and gas tight when properly installed
Passes the 10 feet water stack test - allows basin to withstand water pressure from a 10 ft. vertical pipe (stack) without leaking
Includes one 4" composite inlet hub with rubber insert and Anti-Flotation Device (AFD) to reduce or eliminate the basin from popping up out of the ground when the water table is high
Durable steel cover with inspection plate
LA approved
One piece, seam free construction on all basins
Ready to install for economical and simple installation
Temperature rated 130°F
Basins are not designed to be installed where saturated soil hydrostatic pressure extends above the top of the pit unless the pressure is relieved by an independent drainage system.
Note: Photo is illustrative and may not reflect the actual product.
Zoeller sump and sewage basins collect and contain wastewater before it is removed from a building’s system by way of a submersible sewage pump. It is a critical part of any wastewater (sewage, effluent, sump) system. Commonly constructed with fiberglass or high grade plastic, basins are heavy duty containers. They come in a variety of system types (simplex or duplex), sizes and applications. Some basins operate with multiple types of pumps while others are designed expressly to be paired with a specific pump.
Basins sit below grade while the pump itself sits at the bottom of the basin. How it functions is simple: wastewater enters the basin through an inlet pipe or port. The wastewater accumulates in the basin until it reaches a certain level, at which point your sewage pump will activate (by way of a float switch or preset control) and pump the wastewater through a discharge pipe out of the building to a municipal sewer or septic tank.
Features
Available in high-density polyethylene structural foam, polyethylene or fiberglass
Ideal for residential, commercial and industrial applications
Complete with necessary sealing hardware and flanges
Available with 2” or 3” vent and 2” or 3” discharge
Lid with gasket and 4” cast iron inlet hub with anti-corrosion coating are included with the sewage basins
Centerline of hub is located 10-1/2” (26.7 cm) from top of basin (standard), custom locations available
Polyethylene sewage pump basins are IAPMO approved
For 10’ (3 m) stack test models, refer to charts
Sealed, radon basins for sump pumps in 18” x 22” (46 x 56 cm) and 18” x 30” (46 x 76 cm) sizes
Polyethylene sump basins available with plastic, non-sealed covers in 18" x 22" (46 x 56 cm)
Sewage basins are watertight and gas-tight when properly installed
Durable steel cover with gasket standard on simplex and duplex sewage basins
One-piece, seam-free construction on all basins
Duplex covers include two pump plates and an inspection plate
Ready to install for economical and simple installation
Dimensional engineering data available
Temperature rated 130 °F (54 °C)
Fiberglass models available that will pass the 10’ (3 m) water stack test—refer to charts (L.A. – RR-5311)
Various custom diameters and lengths available in fiberglass, consult factory (also with 10’ (3 m) water stack test)
Consult factory for larger size basins or special applications
Notes
Basins are not designed to be installed where saturated soil hydrostatic pressure extends above the top of the pit unless the pressure is relieved by an independent drainage system. Basin cover vent and discharge seals may be rubber insert or bolted on flange design.
